How to Make a Wooden Smoking Pipe
Introduction: How to Make a Wooden Smoking Pipe
The smoking pipe has been around for ages. It is a very popular item and comes in many different styles from “The Gambler” to “The Churchwarden”. I made a pipe just for the fun of another DIY out in the workshop. But, I do not smoke. There are plenty of ways to make a pipe. You could turn one on the lathe in two separate pieces and then fit them together, or you might want to carve it out of Briar wood and then just drill your way through from the stem to the other end. But, in this easy step-by-step instructable, we will cut two identical pipe shapes out of wood and use a Dremel to carve out the inside and then glue the two halves together.
Step 1: Cut Out the Pipe
Print out the PDF file below on an 8 inch by 11 inch sheet of paper. Cut out the pipe stencil and trace it two times on a piece of wood that is 3/4 of an inch thick. When you trace the pipe, it is very important to make sure that the stem of it is parallel to the wood grain. If you trace it against the wood grain, the stem will be very fragile and will probably break. Next cut out the two pipe shapes. I used my band saw for this, but you could use a jig saw or whatever you have at hand.
Step 2: Drilling the Bowl
You will need a 13/16 drill bit, a drill press (a drill would work, too, but it might not come out as good), and a C clamp. Line up the two halves of the pipe and clamp them together at the bottom. Next, draw a straight line from the top right corner to the bottom left corner. Draw another line from the top left corner to the bottom right corner. Where the two lines intersect is where you are going to drill your hole. Put your 13/16 drill bit in your drill press and drill so that the point on the bit will go straight into the center of the pipe bowl. Go down an inch and stop there.
Step 3: Dig Out the Airway
I have attached an image above. It is a diagram of the pipe airway that you should carve. Copy this onto your pipe cutouts so that when you put the to halves together, the drawing of the airway is on the inside. Use a dremel or a rotary tool to carve this out. don’t go down to deep in the stem. Once you are done with the carving, line up the two halves of your pipe so that the airway is on the inside. Put your lips to the end of the stem and blow. If you could blow through it easily then you are ready to move on to the next step. If not, then keep carving until you can.
Step 4: Glue the Two Halves Together
Take out some strong wood glue and dab a little bit in the blank spots where you haven’t carved anything and put a LITTLE LITTLE bit on the stem because when you put the two halves together, the glue will want to seep into the airway and block it up. Clamp the two halves together or put them in a vice for a few hours. Once it is completely dry, take it out of all the pressure and blow pretty hard into it. If you could blow through, then you’re ready to move on. If not, then place the tip of a flathead screwdriver on the seam where the halves met and tap the top of the screwdriver with a hammer to split them apart. Sand all the glue off and carve the airway a little deeper, and then try to glue them together again.
Step 5: Cut Out the Stem
You could use a hack saw for this or a band saw. I chose the hack saw because I have a little more control over it. Mark a line down each side of the stem, showing where you want to cut. Make sure to widen it at the end where you will blow through. A wider stem will fit more comfortably in one’s mouth. Put your pipe into a vice and tighten it around the bottom. Carefully, cut down each line you drew. If you are using a hack saw, cut in from the side to the point where you stopped cutting on the pencil line. This will let the hack saw turn more freely.
Step 6: Sand the Stem
Use a dremel or rotary tool to carve the corners off of your stem. Keep carving your stem until you think it looks good. Use some 80 grit sandpaper and just sand the stem a little bit. Move up to some finer 150 grit sandpaper and sand the stem some more. Keep moving up in grits until you get to about 500 grit.
Step 7: Carving and Sanding the Bowl Section
I put my pipe in a vice and cut off all the corners of the bowl with a hack saw. Be very careful not to cut too deep into the pipe. Once all your corners are cut off, Take some 80 grit sandpaper and sand all of the bowl section. You could sand by hand, but it takes a very long time, so I used my electric DA sander to get the job done. Once I was done with the 80 grit I went to some 150 grit. I started to sand by hand at this point with the 150 grit. Move up through the same grits that you used on the stem.
Step 8: Finishing Your Pipe
I used wood stain to give my pipe a little more character. But do not stain it if you plan on smoking it. Because when you light it, the pipe will go up in flames and burn to ash. Next, I coated it with lacquer. Once again, do not use lacquer, varnish, wood stain, etc. I only used it because I’m not going to actually smoke it. If you are looking for a finish that will not go up in flames, try some mineral oil. Mineral oil is a food-safe finish and could be used to finish a smoking pipe. Dab a little bit of mineral oil onto a piece of 1500 grit and wet sand your whole pipe. Once the entire pipe is wet sanded, polish it off with a rag or paper towel. Now, you are done! Enjoy your new pipe.
How to Make a Wooden Smoking Pipe: The smoking pipe has been around for ages. It is a very popular item and comes in many different styles from "The Gambler" to "The Churchwarden". I made a pipe just for the fun of another DIY out in the workshop. But, I do not smoke. There are plent…
How to Make a Smoking Pipe
M aking your own smoking pipe is not an easy task, especially if you want the result to be more than just a block of wood with a stem sticking out of it. However, if you possess some patience and practice some determination you may be surprised at just how capable you are of producing your own practical smoking instrument. We sincerely wish that all pipe smokers were inclined to make a pipe of their own, even if only for the sheer pleasure of trying. Now that we’ve begged you, we’ll tell you how!
There are manly men who can make smoking pipes using only sandpaper and hand tools, and then there are the rest of us. Having some larger machinery including a lathe, a bandsaw, a drill press, and a benchtop disc sander makes the process shorter and infinitely easier. We speak from experience as we’ve tried both methods with much greater success in the latter. Though power tools are fun to use and make jobs like drilling the draught hole and chamber, shaping the stummel, and crafting the stem much easier tasks, its obvious that most fledgling pipe makers won’t have one or more of these tools at their disposal at the onset. There’s no reason to start worrying, however. You can make a perfectly capable smoking pipe using tools that most of us already own, or could obtain for a relatively small investment; a hand drill, dremel/rotary tool, and a good set of files and rasps will get you rollin’. You can shape a pipe from start to near finish with good files and rasps, (although it will test those burly arms of yours) and polish it off with some sandpaper. Once you’ve mastered the basics, understand the general concepts of pipe making, and gotten a few pipes under your belt, then it’ll be time to start thinking about investing in tools that will significantly speed up the process and help you create a higher grade smoking instrument. Until then, don’t be discouraged by lackluster results… the David wasn’t Michelangelo’s first sculpture.
Acquiring the right materials is very important. Fabricating a pipe out of pinewood and Play-Doh would be quite cost-effective, but otherwise regrettable. Our pipe-kits come with the best quality Italian briar (from Mimmo himself), and a perfectly shaped and drilled acrylic stem. Here’s a basic description of these 2 essential pipe materials:
Pipes can be made from corncob, meerschaum, olive wood, cherry wood, strawberry wood, ancient morta, clay, and perhaps other materials as well, but briar is considered to be the ultimate material for making pipes. Briar is a type of wood harvested from erica arborea, or “heath tree”, and it’s prized in pipe making for its very high heat tolerance, respiration, hardness, and beautiful grain. It is as expensive as wood goes, mainly because until a heath tree is approximately 40 years old its briar is not considered to be ready for harvesting. Once harvested, the briar must be boiled and dried to remove sap and moisture, but the process is long and must be carefully controlled to prevent the briar blocks from drying too quickly, which can result in splits or fissures in the wood. Briar can be cut two different ways, and each way yields a unique looking block. The more affordable “Ebauchons” are briar blocks that have been cut across the grain, while the pricier “plateaus” are cut with the grain and maintains the craggy outer surface of the briar burl. We carry both an ebauchon and a plateau pipe-kit.
The most commonly used stems by fledgling pipe makers are injection-molded stems that can fit just about any pipe style. They are usually made of ebonite (also called vulcanite), which is a specially treated rubber with a high sulfur content. They can also be made from black or colorful acrylics. Each type has their pros and cons. Ebonite is softer and a bit more comfortable if you grip it in your teeth, but it shows teeth marks more easily and will yellow over time. Acrylic stems are harder, but don’t scratch as easily and won’t fade or change color. Either way, these stems usually need some TLC before they are truly finished, but that’s easier than cutting, shaping, and drilling your own stem from raw ebonite or acrylic rods, which is your other option. Our acrylic pipe-kit stems come polished, with the draught hole trumpeted at the bit end, and their tenons already turned, faced and fitting perfectly into the pre-drilled mortise (no frustration required). If you purchase pre-formed stems elsewhere expect rough edges, a wide, un-turned tenon, and no trumpeting of the draught hole. You’ll have to do all that work yourself.
Preliminary Design and Mechanics
Once you have selected the piece of briar and stem that you will use for your pipe, it’s time to start drilling. Our pipe kits all come pre-drilled to perfection and are ready to be shaped, but here is the process for those with the tooling to do it from scratch. Precision is key here, as a hole drilled at the wrong angle, in the wrong place, or of the wrong diameter can ruin the function of the pipe. Make sure to draw all the holes you will be drilling (draught, mortise chamber) onto the side of the briar block so you can use them as a guide. Getting the sizes, lengths, and angles on there will remove a lot of guesswork. When you’re ready, use a vice to hold the briar block steady as you line up to drill. Whether you are using a drill press or a hand drill, a vice is a must. You’ll want to drill the holes in the following order:
The Draught Hole
The draught hole is pretty important. It’s the channel through which that tasty smoke gets to your mouth, after all. What makes it difficult to get right is that its usually pretty long (and you can’t see through briar to check if it’s straight). If your drilling starts off askew from the lines you’ve drawn on the block, the error will be magnified at the end, so make sure to take your time with this (or just buy a pre-drilled pipe-kit!). It should be drilled with a long, skinny bit. Something in the range of 5/32” or 4mm is about right. Waxing the bit with hard carnauba wax before drilling can help prevent burning the interior of the channel. To make sure you don’t drill the draught hole to far, measure the length of the draught hole line (say it’s 3″). Now mark 3″ up on your drill bit and you’ll know when to stop drilling.
The Mortise and Tenon
Since a good marriage between the mortise and tenon is essential for a good smoker, these are best worked on together. The mortise should be drilled in the same diameter and length as the tenon to avoid creating gaps where moisture will accumulate while smoking. This can be fairly simply accomplished using an appropriately sized forester bit and a drill press or hand drill. You can turn your tenon using either a lathe or a special tenon-turning tool attached to your drill press or a hand drill. Lathes are big and expensive, and using the tenon-turning tool gave us nightmares, but unfortunately there aren’t many other options out there. Popular diameters for the mortise are 9/32” and 5/16”, so turn your tenon accordingly, checking the fit constantly (tight, but not too tight being the idea fit).
The chamber is a tough one, since the bottom of your chamber should be conical or round, not square as would be achieved with a Forstner bit. There are specially made bits for drilling tobacco chambers ranging in price from a few dollars to $100+, but the cheap ones will do for your first few pipes! If you have bench grinder you can round off the edges of cheap spade bit, or just pick up a pre-rounded spade bit from one of several sources online. 3/4” is the most popular size for tobacco chambers, but for larger pipes, you may choose to go with 7/8”. Use your chamber drawing as a guide and drill slowly but surely, checking for signs of the draft hole often the deeper you go. Once you’ve drilled deep enough that the entire diameter of the draught hole is barely visible, stop! You’re done!
The Fun Part… Mostly
Getting the mechanics just right or even mostly right can be quite frustrating. That’s why most fledgling pipe makers are quite happy to move on to the more creative and rewarding parts like shaping and staining (our pipe-kits allow you to start your pipe making journey right at this step!). These steps are not without their sand-traps however. Just wait until you sand the sides of the bowl down to far and can see light filtering in through a hole in the side of your chamber. Or, when you think you did a great job finish sanding only to find out your pipe is a scratched up mess after you’ve done the final buffing. Don’t worry, we’ve got the directions you need and some tips to help you avoid some rookie mistakes.
Shaping is fun… really fun. This is when the vision of you pipe (however good or bad it was) starts to become reality. How easy this task is accomplished once again depends upon the tools at your disposal. I’ll break it down this way…
You have a:
Awesome! Almost all the pros make a good deal of their pipes this way. Shaping will be limited to shapes that have congruent sides (i.e. billiards, princes, etc.), but in theory this method produces the most consistent pipes. With a metal lathe you can also opt to shape before you drill although we don’t recommend you try this until you’ve got some experience. For more on “shaping before drilling” check out the Pipe Maker’s Forum.
Disc or belt sander
You can create any pipe shape you want! Every professional pipe maker has one (or a few) of these and most of the great Danish pipe makers use disc sanders exclusively for shaping. You will want to get sanding discs of various grits (think 60 to 180 grit), and work your way up as your pipe shape becomes more defined.
Dremel or rotary tool
Shaping a pipe from start to finish is definitely doable with a dremel tool. It’s going to be a longer road and you’ll need much more patience, but it can be done… we’ve done it. You can get the little barrel shaped sanding discs in various grits so you can shave off more or less wood depending on what shaping stage you’re at. If you go with a Dremel, stick to a more simple, tried-and-true shape like a billiard, apple. Anything much more complex would be pushing the limits in our opinion.
Files and rasps
These technically can get the job done, but that’s really pushing it. If all you had to work with was files and rasps it would take quite a long time to finish and the end product wouldn’t look as polished. Regardless, files and rasps are essential additions to any one of the shaping methods/tools above. They are necessary for getting in and removing briar from tight spaces that would otherwise be nearly impossible with just the above tools.
Fingernails, kitchen knife, broken bottle
Are you a descendant of Michelangelo? No… good luck!
Sanding, Sanding, and More Sanding
Only move on to this step until you have your shape completely defined using one of the above shaping methods. If you get ants in your pants and move on to early, thinking you can remove a lot of the remaining unwanted briar with sand paper, you will realize that you were stupid. At this point, buckle in, put some music on and get ready to sand your fingerprints away. Ok, we’re being dramatic, but this is both a tedious and extremely important stage. Starting with 120 grit sandpaper, you are going to be sanding every nook and cranny of your pipe. Then move onto 220, 320, 500, and finally (if you want it to be literally as smooth as a baby’s bottom) 600 grit. Trust us, if you don’t sand diligently with every grit, you WILL be surprised at how many scratches are left after the final buffing that you could not see while sanding. If that isn’t that important to you, than no worries.
Pre and Final Staining
The pipe makers stain of choice is Fiebings leather dye. It comes in a variety of colors and if none of those suit your fancy, you can mix them to your heart’s content. It is readily available at Fiebings own website. All it takes to apply the dye is a pipe cleaner.
Pre-staining is optional, but does lead to a finished pipe with greater grain contrast. It involves staining the whole pipe in black, or a darker dye color, and then sanding it away, with the highest grit you finished sanding at, until only the stain deeply absorbed into the grain remains.
Whether you pre-stain or not, final staining comes next. It is quick and simple. Using a pipe cleaner, stain the whole pipe with your desired color, working quickly so you don’t get a blotchy finish. One coat usually does the trick, but if you want a darker finish go for a second. Oh, and our friend Wayne Teipen would be disappointed with us if we didn’t stress the fact that you should never stain your chamber! Just stick a cork in the chamber (no joke) before you begin and then stain away. Let the pipe dry to the touch (about 10 minutes if it’s not very humid) before continuing.
Ahhhhh you’re almost there. Now ideally you would have a benchtop buffing setup for this. We use a bench grinder with the guards and grinding stones removed, replaced with muslin and flannel buffing wheels. If you don’t have this setup, you can get miniature buffing wheels for your Dremel/rotary tool.
You’ll want to get yourself some red or brown tripoli compound and carnauba wax. Get your buffing wheels spinning and hold the tripoli compound up to the muslin wheel for just a couple of seconds to apply it to the wheel. Bring your pipe up to the wheel (steady now) and begin to buff the whole pipe. Make sure you have a firm grip on the pipe and don’t push it into the wheel too aggressively or it will rip it out of your hands and bounce it all over your shop (as Phil can attest to MANY times). Tripoli compound is actually a very very fine abrasive that removes teeny tiny scratches from the surface of the pipe.
Finally, repeat on the flannel wheel with the carnauba wax. This is when your work will really start to shine and your diligent sanding proved, because if your pipe still has scratches, this is when they will show up. But, we know you’ve done a flawless job!
How to Make a Smoking Pipe M aking your own smoking pipe is not an easy task, especially if you want the result to be more than just a block of wood with a stem sticking out of it. However, if